A Guide to Basic Appliqué Projects
- Fabric (Scraps left over from another project work great here)
- Fusible web (I use Heat’n Bond Lite)
- Sewing shears
- Tear-away stabilizer
- Additional embellishments: ribbon, buttons, rhinestones, etc. (optional)
- Garment to be embellished
Step 1: Select an Appliqué Template
Step 2: Select Your Fabric
- Quilting cotton
- Jersey Knit
- Leather, Suede and Ultra Suede
- Marine vinyl
Step 3: Apply Fusible Web to the Wrong Side of Your Material
Remove one side of the backing from your fusible web sections. With the wrong side of your material facing up, apply the fusible web to the material. Your iron should be set at a cotton setting with no steam.
Step 4: Trace Appliqué Templates onto the Fusible Web Backing
With the right side of your templates facing down, trace each layer onto its respective fusible web-backed fabric piece. Important: You will need to trace a mirror image of your design so that your appliqué will display correctly once it’s affixed to your garment.
Step 5: Cut Out Appliqué Pieces and Iron to Garment
Using sharp sewing shears, carefully cut out each layer of your appliqué design. It is important to cut very carefully, as this edge will be visible on your finished garment. Remove the paper backing from these pieces, and then arrange them, starting with the bottom-most layer and working up, onto your garment in your desired configuration. Using your hot iron, carefully press these pieces to affix them to your garment. Be careful not to drag your iron across your design, as this could cause your appliqué design pieces to shift. Instead, lift the iron up and then place it down onto the next section of your design as you work.
Step 6: Pin Stabilizer to the Inside of Your Garment
This is a step that often gets overlooked in basic appliqué projects, but it is incredibly important and not to be skipped! Cut a piece of tear-away stabilizer (I love Sulky stabilizers) that is just larger than the entirety of your appliqué design. Pin the stabilizer piece to the inside of your garment directly behind your appliqué design. Why use stabilizer? It will prevent ugly puckering during the next step, which will give your finished project a much more professional look.
Step 7: Stitch Your Appliqué Design into Place
You have a few different stitch options for securing your design to your garment.
- Satin stitch (the traditional option)
- A zig-zag (this minimizes fraying)
- A straight stitch (by far the easiest option, but does allow some fraying to occur)
There are some sewing purists who feel very strongly that appliqué can only be done properly when finished with a satin stitch, which is essentially very tight zig-zag stitch. If you find that look to be the most appealing to you, this is a great video how-to.
Although I do love the more traditional look of satin stitch appliqué, I almost always finish my appliqués with a simple machine straight stitch. This method is far less time consuming and complex than a satin stitch, and although the results are not as durable as a satin stitch would be, I am fine with that. On boys’ garments, especially, I think the fraying that occurs can actually add character to the finished project.
To finish with a straight stitch as I’ve done here, use a straight stitch set to a medium length (I set my machine at 3), and stitch all the way around your design, as closely as you can to the outer edge. Make sure to backtack at the beginning and end of your stitches so they don’t come loose later on. Work in sections as you stitch, stitching around each layer of the design as you go. Make sure not to try to work too quickly here: slow and steady is the way to go! If you find curves to be too challenging, stop your machine with the needle down, lift the presser foot, and carefully pivot just a touch. Lower the presser foot, stitch one or two times, and then repeat. Although this process does take a fair amount of time, this will allow you to have a steady, well-rounded line of stitches even around the most challenging curves.
If you prefer to use a zig-zag stitch, stitch all the way around the perimeter of the design as you would with a straight stitch, making sure that the “zig” of the stitch falls within the design, and the “zag” of the stitch falls just outside of it. This way the entire outer edge will be protected from fraying. I think designs finished with a zig-zag have a more homespun, cozy feel.
An important note about thread color: For appliqué beginners, I highly recommend using a thread color that matches well with the material in your appliqué design. For instance, in my Mickey shirt below, I used black thread to match the black fabric of the bottom layer, and white thread to blend well with the top striped layer. It is extremely difficult even for experienced sewists to make stitching look completely polished when using a thread color that contrasts considerably with the background!
Step 8: Tear Away Stabilizer
Once your design is stitched into place, turn the garment inside out and tear away the stabilizer. A pair of tweezers can be handy for getting rid of the any tiny pieces that remain.
Step 9: Apply Additional Embellishments to Your Design (Optional)
If desired, use a needle and thread to affix any additional embellishments to your design by hand. Great options here are bows, buttons and beads.